Home > Problem Solving > Remove Soap Scum from Natural Stone Walls

HOW TO REMOVE SOAP SCUM FROM NATURAL STONE SHOWER WALLS

Step-by-step instructions for marble, limestone, travertine, terrazzo and encaustic shower walls and splashbacks, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Soap scum on stone walls

Apply, dwell, scrub, rinse

Stone Gel+ is a Professional Grade, ready-to-use, high viscosity alkaline cling gel cleaner, conditioner and commercial grade disinfectant. It is non-acidic, so it is suitable for acid-sensitive stone, and it clings to shower walls to help remove soap scum, body oils, dirt and grime.

  • Ready to use: no mixing, apply neat
  • Non-acidic: suitable for marble, limestone, travertine, terrazzo and encaustic
  • Minimum 10 minutes dwell time. Don't let it dry on the surface
  • Scrub with the Scrub'N'Clean Kit - Walls, rinse and wipe dry
  • Never use acid cleaners on these surfaces: they can etch and dull the stone
  • Protect the floor, drain and fixtures. Always test first
  • Floors: see soap scum on natural stone or terrazzo & encaustic
Stone Gel+ 1 litre
STONE GEL+ · WALLS
1 L · 4 L

What is soap scum, and why no acids?

Soap scum is the dull, whitish film left on shower walls when soap, shampoo and body oils combine with minerals in the water. It builds up in layers, dulls the stone and gives mould something to feed on.

Marble, limestone, travertine, terrazzo and encaustic tiles are acid-sensitive: acidic bathroom cleaners can etch and dull them. Use a non-acidic cleaner such as Stone Gel+, and always test first.

TIP: once clean and dry, seal with Aqua-Seal Gold+ to help reduce absorption and make soap scum easier to wipe off.

Soap scum on a marble shower wall

Soap scum on a marble shower wall

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Etch marks or dull, damaged polish: cleaning won't restore polish
  • Skin (hard surface disinfectant only)

What you'll need

  • Stone Gel+ (ready to use, no mixing)
  • Scrub'N'Clean Kit - Walls, sponge or white nylon pad
  • Narrow grout brush for the joints
  • Towels or plastic sheet to protect the floor, drain and fixtures
  • Sponge, spray bottle or handheld shower for rinsing, plus clean water
  • Clean cotton towels to wipe dry
  • Gloves and eye protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C. Work out of direct hot sun
  • Protect the floor, drain, tapware, fixtures and any non-recommended surfaces
  • Wipe or rinse off loose dirt first
  • Work in small sections you can keep wet for the full dwell time
  • Keep children and pets away until the area is rinsed

Step-by-step

Prepare → Treat → Remove + rinse
Protect and wipe down1Prepare

Protect and wipe down

Cover the floor, drain and tapware with towels or plastic, then wipe or rinse loose dirt off the wall.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try Stone Gel+ on a small, hidden spot to check ease of application, dwell time, colour stability and results.

Apply Stone Gel+ neat3Treat

Apply Stone Gel+ neat

Ready to use, no dilution. Pour onto a gloved hand, sponge or white nylon pad and smear evenly over the section of wall. Work top to bottom in small sections.

Allow at least 10 minutes dwell time4Treat

Allow at least 10 minutes dwell time

The cling gel stays on the wall. Don't allow the product to dry on the surface: add more Stone Gel+ to keep it wet and active.

Scrub the wall5Treat

Scrub the wall

Scrub with the Scrub'N'Clean Kit - Walls or a white nylon pad, top to bottom.

Scrub the grout joints6Treat

Scrub the grout joints

Use a narrow grout brush on dirty grout joints and corners.

Rinse and wipe dry7Remove + rinse

Rinse and wipe dry

Remove the dirty gel with a sponge, then rinse thoroughly with clean water from a sponge, spray or handheld shower. Wipe dry with clean towels.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the wall once it is fully dry and repeat the process as necessary.

How to use: Stone Gel+

DilutionNone, use neat (ready to use)
Apply withGloved hand, sponge or white nylon pad
Dwell timeMinimum 10 minutes, keep wet
Surface temp.4°C to 32°C
Pack sizes1 L · 4 L

Why a cling gel for walls?

Liquid cleaners run straight down a wall. The high viscosity gel stays on the stone for the full 10 minutes to soften soap scum, and it is non-acidic, so it is suitable for marble, limestone and travertine. No buckets or mixing.

Tips for the best result

  • Work top to bottom in small sections
  • Never use vinegar or acidic bathroom cleaners on marble, limestone or travertine
  • Squeegee or wipe walls dry after each shower to help reduce build-up
  • Clean weekly with EzyClean+ (pH neutral)
  • Floors: see soap scum on natural stone floors
  • Re-seal when water no longer beads on the surface

Aftercare

Aqua-Seal Gold+

Aqua-Seal Gold+: re-seal once clean and dry, and when water no longer beads.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first. May dull or discolour some sensitive surfaces
  • Wear gloves and eye protection: causes serious eye damage. Avoid skin contact
  • Do NOT breathe mist, vapours or spray
  • Use when the surface is between 4°C and 32°C
  • Do NOT allow contact with non-recommended surfaces. Do NOT mix with other chemicals
  • May affect some dark grouts and grout colourants
  • Regular use of alkaline cleaners can affect sealers, coatings, grout colourants and floor finishes
  • Hard surface disinfectant only. Do NOT use on skin
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface, how heavy the build-up is, how long it has been there and whether the surface was sealed. Cleaning will not remove etch marks or restore polish to damaged stone.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Sealers Plus