Home > Problem Solving > Remove Leaf Stains from Stone, Tiles, Pavers & Concrete

HOW TO REMOVE LEAF STAINS FROM STONE, TILES, PAVERS & CONCRETE

Step-by-step instructions for natural stone, ceramic, porcelain, encaustic and terrazzo tiles, concrete, grout, pavers and bricks, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Leaf & tannin stains

Mix, dwell, scrub, rinse

Active Plus is an easy to use, 100% actives, super concentrated, triple action cleaner, deodoriser and stain remover. Mixed with warm water, it helps remove leaf and tannin stains, algae, mould, mildew, dirt and grime.

  • Powder: mix 30 g per 1 litre of warm water (60 g for extreme heavy duty)
  • Use hot water for better results (never boiling)
  • Allow 5–10 minutes dwell time. Don't let it dry on the surface
  • Scrub, pick up with a wet vac, then rinse thoroughly
  • Safe on natural stone, ceramic & porcelain tile, grout & concrete. Always test first
  • Stubborn, deep-set stains: use the paste method
  • Keep away from non-recommended surfaces
Active Plus 2 kg
ACTIVE PLUS
300 g · 1 kg · 2 kg

What causes leaf stains?

Leaves, bark, flowers and seed pods release tannins and natural dyes as they get wet and break down. On porous surfaces such as natural stone, concrete, pavers and grout, these soak in and leave brown or orange leaf-shaped marks.

The longer a stain sits, the deeper it can go, so treat it early. How well it lifts depends on the surface, how long the stain has been there and whether the surface was sealed.

TIP: once the stain is removed and the surface is dry, re-seal with a premium sealer such as Aqua-Seal Gold+ to help reduce future staining and make cleaning easier.

Watch the video

Remove Leaf & Tannin Stains from Travertine and Other Natural Stone – Active Plus

Remove Leaf & Tannin Stains from Travertine and Other Natural Stone – Active Plus

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Plants, soil and metals (keep it away)
  • Etch marks or dull, damaged polish: it won't remove etching or restore polish

What you'll need

  • Active Plus
  • Scrub'N'Clean Kit, white nylon pad, broom or scrub brush
  • Plastic bucket and warm/hot water (not boiling)
  • Kitchen scales or a measuring cup
  • Wet vac (recommended) to pick up the dirty solution
  • Bucket plus plenty of clean water for rinsing
  • Gloves, eye, skin and foot protection
  • Paste method: plastic wrap, residue-free tape, plastic spatula, paper towels

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Sweep away leaves and debris
  • Keep the solution away from plants, soil and metals
  • Mix only what you'll use: never cover or store mixed solution
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Sweep and pre-wet1Prepare

Sweep and pre-wet

Sweep away leaves and debris, then pre-wet the surface with clean water.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try the solution on a small, hidden spot to check surface colour stability and how well the stain lifts.

Mix Active Plus3Treat

Mix Active Plus

Stir 30 g of Active Plus per 1 litre of clean, warm water into a plastic bucket, e.g. 300 g in 10 litres. For better results use hot water (never boiling). Stir until it dissolves.

Apply generously4Treat

Apply generously

Apply the solution generously to the surface with a clean mop. Clean large areas in sections.

Allow 5–10 minutes dwell time5Treat

Allow 5–10 minutes dwell time

Allow to dwell for 5–10 minutes. Don't allow the product to dry on the surface: add more solution to keep it wet and active.

Scrub6Treat

Scrub

Scrub with a Scrub'N'Clean Kit, white nylon pad, broom or brush.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac, then rinse thoroughly with clean water.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry and repeat as necessary. Stubborn stain? Use the paste method below.

Mixing rates: Active Plus

UsePer 1 litrePer 10 litre bucket
Heavy duty clean30 g in warm/hot water300 g in 10 L
Extreme heavy duty clean60 g in warm/hot water600 g in 10 L

Dispose of any unused mixed solution after 4 hours.

Stubborn stains: paste method

  1. Mix Active Plus with warm water to a thick toothpaste / peanut butter consistency
  2. Apply a finger-thick, even coat over the stain, covering slightly more than the stain
  3. Optional: cover with plastic wrap, tape the edges with residue-free tape and poke a few holes in the wrap
  4. Leave until the paste dries (24–48 hours depending on conditions), or for at least 24 hours
  5. Lift off with a plastic spatula, mist with clean water and rub lightly with a white nylon pad or brush
  6. Rinse thoroughly with clean water, dry with paper towels and repeat as necessary

Tips for the best result

  • Treat leaf stains early: the longer they sit, the deeper they go
  • Sweep leaves regularly, especially under trees and before rain
  • Use hot (not boiling) water for better results
  • Work in sections you can keep wet, and never let the solution dry on the surface
  • For deep-set, stubborn stains, see the Stain Removal Guide
  • Once clean and dry, re-seal to help reduce future staining

Aftercare

Aqua-Seal Gold+

Aqua-Seal Gold+: re-seal once the stain is removed and the surface is dry.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first
  • Take care if using hot water to prevent scalding. Do not use boiling water
  • Wear skin, eye and foot protection
  • Use when the surface is between 4°C and 32°C
  • Keep away from plants, soil and metals
  • Once mixed, do NOT cover or store mixed solution
  • Dispose of any unused solution after 4 hours by flushing with plenty of clean water into a toilet or drain
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface stained, the type of stain, how long the stain has been in place and whether the surface was sealed or unsealed. Active Plus will not remove etch marks or restore polish to damaged areas.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Sealers Plus