Ultra Block
Installation Sealer for Pre-Sealing and Six Sided / Dip Sealing
ULTRA-BLOCK – INSTALLATION SEALER FOR PRE-SEALING AND SIX SIDED SEALING.
Ultra-Block is an economical water based specialty sealer formulated for six sided, dip-sealing, underside & pre-grouting sealing. Helps resist staining caused by water soluble minerals (including picture framing effect) which are normally absorbed through the back of the stone during installation. It also helps resist ef orescence migration & adhesive blotch marks. Can also be used as a pre-grouting sealer. Allows moisture vapour transmission (MVT).
Key Features
Makes Grouting and Grout Clean Up Process Easier;- Helps Consolidate Stone – Minimises Staining from Handling, Grout and Adhesive;
- Reduces Picture Framing, Mineral Staining and Efflorescence;
- Water Based – Low VOC – Non Flammable Formulation.
All the important information
Available sizes



Where to use
For domestic, commercial, indoor, outdoor, wall and floor applications, e.g. kitchen, living and entertaining areas, bathrooms, pool surrounds, patios, bench-tops, table tops, building facades etc.
For homes, hotels, motels, resorts, schools, child and aged care facilities, supermarkets, restaurants, bars etc.
Precautions
- Read entire label, SDS and technical bulletin before using
- Wear appropriate gloves, skin and eye protection
- Use when surface temperature is between 4\u00b0C and 32\u00b0C
- Surface must be clean, dry and free from sealers and coatings
- Avoid Ultra-Block contact with the top surface if you intend to use an enhancing type sealer. Do not use Ultra-Block on any side if Gloss'N'Seal / Satin'N'Seal will be applied (they cannot be used if Ultra-Block is used first)
- Apply only one (1) coat of Ultra-Block if six sided sealing
- Do not saturate the open grout joints
- If using a dark or contrasting grout, apply Grout Release+ before grouting and only after Ultra-Block has cured
- Use Aqua-Seal Gold+ as a final sealer for premium stain resistance and performance. Ideal for food and high traffic areas
Test first: always test first in an inconspicuous area to determine ease of application, number of coats, colour stability and desired results. The end user must determine suitability of the product for their use.
Surface preparation
Use XtremeClean+ as per label instructions to ensure a clean, dry surface before starting.
How to use pre-sealing
- Apply sealer to clean, dry surface using a sealer applicator, pump sprayer, sealer sponge, brush, paint roller or paint pad
- Ensure even coat and coverage then work product in thoroughly
- After 5-10 minutes, wipe the surface completely dry with absorbent paper or cotton towels to remove any excess
- Do not allow product to dry on the surface
- Allow to cure minimum 24 hours before installation or grouting
How to use dip-sealing / six sided sealing
- Fill a clean tray with Ultra-Block and fully submerge stone or tile for 30-60 seconds (the longer the better)
- After 5-10 minutes, wipe the surface completely dry with absorbent paper or cotton towels to remove any excess sealer
- Do not allow product to dry on the surface
- If sealing prior to installation, lean sealed stone vertically against a wall. Place a plastic wedge or spacer between each piece so the tiles are not touching, allowing a gap of 5-10cm between each tile for air circulation and proper curing
- Allow to cure minimum 24 hours before installation or grouting
- After 24 hours and before installation, scrub back the surface of the stone with a white nylon pad or brush to remove any sealer residue
Quick guide: pour into a suitable sized container, submerge tile or stone for 30-60 seconds, after 5-10 minutes wipe completely dry, allow to dry and cure for 24 hours before installing. If using contrasting grout apply Grout Release+, then grout the surface as usual.
Underside sealing note
Treat the sealed underside as low porosity. Ultra-Block will reduce the porosity of the underside sealed surface. Contact your adhesive supplier for specification of an appropriate adhesive suitable for installing low porosity/dense surfaces. The sealed underside surface should be thoroughly back buttered using the flat side of a trowel with adhesive to ensure proper coverage and adhesion. Follow the adhesive manufacturer's instructions for the selected adhesive and ensure industry installation standards are followed.
Limitations
Sealer is not a waterproofing agent and will not prevent surface wear or etching from harsh or acidic chemicals. For best stain resistance, apply a premium sealer as a final sealer, e.g. Aqua-Seal Gold+.
Coverage
Approximately 40-160 m\u00b2 per 4 litre per coat. It will vary depending on the density, porosity, texture and absorption. Also weather conditions, the application method and number of coats required.
Coverage calculator
Handling, storage, clean up & first aid
- Close container tightly after use and store between 4\u00b0C and 32\u00b0C
- Do not re-use container. Discard in rubbish
- Clean tools and clothes with water before they dry
First aid: contact a doctor or Poisons Information Centre (Aust 131-126, NZ 0800 764 766).
- Inhalation: first aid not generally required
- Ingestion: do not induce vomiting. Give water to drink
- Eyes: immediately flush eyes with clean, running water for at least 5 minutes and see a doctor
- Skin: wash gently with plenty of water
Customer reviews
Used Ultra-Block?
Explore the range
More from Sealers Plus
Good, Better or Best protection, from natural look to colour enhancing and gloss finishes.
View all Sealers →Biodegradable cleaners to clean and maintain stone, tile and grout without harming your sealer.
View all Cleaners →Targeted products to help remove efflorescence, grout haze, rust, stains and mould, plus anti-slip.
View all Problem Solvers →Applicators, scrubbing kits and care kits that make sealing and cleaning easier.
View all Accessories →















































