Home > Products > Sealers > Spray’N’Seal
Spray’N’Seal
Premium Aerosol Sealer (Best)
SPRAY’N’SEAL – PREMIUM NATURAL LOOK AEROSOL SEALER FOR STONE, TILES, GROUT, ENCAUSTICS, TERRAZZO ETC
Spray’N’Seal™ is a breathable, premium, natural look sealer to provide maximum stain resistance to stone, tile, mosaics, grout & other porous surfaces. It is non-yellowing, non-coating and UV resistant. Can be used on newly installed grout 2 hours after grouting however for best performance allow grout to fully cure before sealing. Utilises the latest Nano-AQS™ & Rapid-Seal C6 FluoroTM Technology to provide good stain resistance after only 4 hours. Can also be used as a pre-grouting sealer. Allows excellent Moisture Vapour Transmission (MVT). For interior & exterior. USE: For Porous Stone, Tile, Grout, Glass, Mosaics, Canvas, Wood etc
Key Features
- Maximum Stain Resistance Against Oil, Food & Grime;
- Reduces Freeze/Thaw Damage, Spalling & Efflorescence
- UV Resistant – Non Flammable – Inhibits Mould & Mildew;
- C6 Fluoro Seal plus Rapid Seal Technology – Cures in 4 hours*
- Ideal for high traffic, food preparation & serving areas – Non Toxic
- For Wall, Floor, Interior, Exterior, Domestic & Commercial Applications.
AVAILABLE SIZES
AVAILABLE SIZE
TEST FIRST
PRECAUTIONS
- Read entire label, SDS & product technical bulletin before using;
- Wear appropriate skin & eye protection & use in a well ventilated area or wear a suitable mask;
- Surface must be clean & completely dry and free from any other sealers & coatings.
- Use when surface temperature is between 4°C & 32°C.
- Do not allow contact with any non-recommended surfaces;
- Do NOT use on underside of tile or stone;
- May slightly darken some surfaces;
PRE-GROUT SEALING
- Pre-seal the front/top surface before installation or 4 hours after installation.
- Do NOT saturate the open grout joints;
- Allow minimum 4 hours cure time before grouting;
- If using dark or contrasting grout, apply Grout Release Pro after Spray’N’Seal or Ultra-Block has cured, then grout.
PREPARATION
Use XtremeClean as per label instructions to clean and prepare surface to be sealed.
APPLICATION INSTRUCTIONS
- Sweep, vacuum or wipe surface clean;
- Shake can well before using;
- Apply product directly to clean, dry surface from approximately 20-30cm and spray in an even, slow sweeping motion;
- If only sealing grout joints minimize spray on the surrounding areas;
- If severe over-spray occurs, wipe the surface DRY with absorbent paper or cotton towels after 5-10 minutes, to remove any excess sealer;
- If 2 or more coats are required, allow minimum 30 minutes between coats and follow label instructions for each coat;
- The surface is ready for light traffic after 2 hours;
- Keep surface dry for minimum 24 hours.
LIMITATIONS
- Sealer is NOT a waterproofing agent and will not prevent surface wear, scuff marks or etching from harsh or acidic chemicals.
- Spills should be wiped up immediately to help minimise staining
- The surface is ready for light traffic after 2 hours;
- Keep surface dry for minimum 24 hours.
EXPECTED WEAR
MAINTENANCE
- EzyClean for routine, everyday cleaning;
- Boost for routine cleaning & help prolong sealer life span;
- XtremeClean for periodic heavy duty cleaning;
- AquaGuard for spary’n’wipe gleaming of bench tops plus help prolong sealer lifespan;
- Clean’N’Gleam for one step spray’n’wipe closing of bench tops.
HANDLING, STORAGE & CLEANUP
- PRESSURISED DISPENSER.
- PROTECT FROM SUNLIGHT & DO NOT EXPOSE TO TEMPERATURES EXCEEDING 50°C.
- DO NOT PIERCE OR BURN EVEN WHEN EMPTY.
- DO NOT RE-USE EMPTY CONTAINER.
- DISCARD IN RUBBISH OR RECYCLE.
FIRST AID
- Ingestion: Do not induce vomiting. Give water or milk to drink.
- Eyes: Immediately flush eyes with clean, running water for at least 15 minutes & see a doctor.
- Skin & Hair: Remove contaminated clothing. Immediately wash contaminated skin & hair with plenty of water.
- Inhalation: Remove victim from exposure to fresh air. Seek medical advice.
- General: If irritation persists or feeling unwell, seek medical attention.
- Additional information available on SDS.
SAFETY PRECAUTIONS
PROPELLANT: Hydrocarbon. UN1950 – AEROSOL Contains: Heptane
BEWARE Intentional misuse by deliberately concentrating and inhaling contents can be harmful or fatal.
Spray’N’Seal Demonstration
Use For
Accessories
The Aqua-Seal STS™ range of accessories are designed to make sealing, cleaning and problem solving applications easier.
Cleaning Products
The Aqua-Seal STS™ range of biodegradable Cleaners is formulated to clean & maintain your surface without fear of damage to your tile, stone or sealer. Our range of cleaners is for domestic & commercial use. Safe and effective for your routine daily clean or your periodic heavy duty clean.
Other Sealer Options
The Aqua-Seal STS™ range of Sealers are formulated to provide either a Good, Better or Best type of performance based on the needs of the customer. The better the sealer then the better the protection, the longer the reaction time and the longer the life span of the sealer.
Problem Solver Options
Stone and tile areas exhibit many specific problems such as efflorescence, grout residue and mineral staining. The Aqua-Seal STS™ range of Problem Solvers is designed to help solve these issues as safely and effectively as possible. There’s simply no other range of problem solvers for stone, tile, concrete & grout as comprehensive as Aqua-Seal STS™.
Important Information
LIMITATIONS:
- Sealer is NOT a waterproofing agent and will not prevent surface wear, scuff marks or etching from harsh or acidic chemicals. Spills should be wiped up immediately to help minimise staining.
TEST FIRST:
- Due to the nature of different surfaces, you should do a few inconspicuous test areas following the label instructions to determine ease of application, surface colour stability and desired results. The end user must determine the suitability of the product for their intended use.