Home > Surface Finder > Terrazzo > Textured
Textured TerrazzoClean, seal & maintain guide
Textured terrazzo covers several finishes formed by moulding or mechanically working the face to leave raised and recessed areas. It feels uneven, with the chip pattern showing through the relief. Absorbency varies, though exposed cement tends to draw in spills. Uses include entrance flooring, paving and feature walls. Natural Look and Colour Enhanced are available. Recesses can need extra cleaning attention.

Recommended for textured terrazzo
Exactly what our Product Selector recommends for textured terrazzo, with coats and coverage from the product labels.
| Desired look | Product | Use on | m² per 1 L per coat | Coats |
|---|---|---|---|---|
| Natural Look | Floors | 15–20 | Min 2 | |
| Colour Enhanced | Floors | 15–20 | Min 2 |
Before installing & grouting
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-grout release coating | 2.5–20 | 1 |
PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around terrazzo. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed
Clean before sealing
The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.

Strip first with Aqua-Strip, then rinse with clean water.
Stain removal & problem solving
Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.
| Problem | Use (try in this order) |
|---|---|
| Grout haze | |
| Efflorescence (white salts) | |
| Rust & iron stains | |
| Fertiliser | |
| Oil, grease & food | |
| Wine, coffee & tea | |
| Mould, mildew & algae | |
| Hard water marks | |
| Etch marks (dull spots) | Not a stain: etching is surface damage that sealing can't prevent. A stone restoration technician can hone or re-polish it. Call us on +61 2 9521-4000 for advice. |
Cleaning & care tips
- New terrazzo: remove polishing slurry haze with Haze Away (non-acidic) before sealing.
- Use entrance matting at every door in commercial sites.
- Dull traffic lanes usually need re-honing, not more sealer.
- Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
- Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
Take this textured terrazzo guide with you
Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.
Important Note
Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.
