Home > Surface Finder > Terrazzo > Sandblasted

Surface Finder · Terrazzo

Sandblasted TerrazzoClean, seal & maintain guide

Blasting the surface with abrasive particles removes small amounts of material and exposes the terrazzo’s chip-and-binder pattern. The face feels grainy, with little glare, and cement-based versions tend to take up liquids readily. Typical uses include garden paths, courtyards and external steps. The available looks are Natural Look and Colour Enhanced. Regular cleaning helps lift dirt from the small pits.

Looks our Product Selector recommends:Natural LookColour Enhanced
Sandblasted Terrazzo close up

PRODUCT SELECTOR RECOMMENDATIONS FOR SANDBLASTED TERRAZZO

Product Selector

Recommended for sandblasted terrazzo

Exactly what our Product Selector recommends for sandblasted terrazzo, with coats and coverage from the product labels.

Desired lookProductUse onm² per 1 L
per coat
Coats
Natural LookFloors15–20Min 2
Colour EnhancedFloors15–20Min 2
▶ Watch howWatch: Aqua-Seal Gold+How to colour enhance & seal
Approximate only. Coverage varies with the density, porosity, texture and absorption of the surface, weather, application method and number of coats. m² per 1 L = the min–max coverage from the product labels.
Open the Product Selector ›

BEFORE INSTALLING & GROUTING FOR SANDBLASTED TERRAZZO

Installers

Before installing & grouting

StepProductm²/LCoats
Pre-seal top surface before installation or before grouting15–201
Pre-grout release coating2.5–201
▶ Watch howPre-seal with Enhance'N'Seal
Pre-sealing the top surface before installation or grouting makes grout clean-up easier.
TIP: Use Haze Away in the final rinse during the grouting process to make grout clean-up easier and help prevent grout haze.
Eff-Shield+

PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around terrazzo. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed

CLEANING SANDBLASTED TERRAZZO BEFORE SEALING

Step 1 · Clean

Clean before sealing

The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

XtremeClean+
Existing surfaces · clean & prepare

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.

Aqua-Strip

Strip first with Aqua-Strip, then rinse with clean water.

▶ Watch howDeep clean with XtremeClean+Remove organic stains with Active Plus

STAIN REMOVAL & PROBLEM SOLVING FOR SANDBLASTED TERRAZZO

Problem solvers

Stain removal & problem solving

Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.

ProblemUse (try in this order)
Grout haze
Efflorescence (white salts)
Rust & iron stains
Fertiliser
Oil, grease & food
Wine, coffee & tea
Mould, mildew & algae
Hard water marks
Etch marks (dull spots)Not a stain: etching is surface damage that sealing can't prevent. A stone restoration technician can hone or re-polish it. Call us on +61 2 9521-4000 for advice.
▶ Watch howMicroScrub how-toRemove rust with Rust AwayRemove leaf & tannin stains with Active PlusDeep clean with XtremeClean+Which stain remover? Product Selector guide

CLEANING & CARE TIPS FOR SANDBLASTED TERRAZZO

Pro tips

Cleaning & care tips

Never pressure wash. High-pressure water can exfoliate and degrade the surface and reduce the sealer's performance. It can also drive water deep into the surface and bring up mineral blooming and efflorescence. Clean with a mop, brush or scrubbing machine and rinse with a low-pressure garden hose instead.
  • New terrazzo: remove polishing slurry haze with Haze Away (non-acidic) before sealing.
  • Use entrance matting at every door in commercial sites.
  • Dull traffic lanes usually need re-honing, not more sealer.
  • Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
  • Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
▶ Watch howWeekly clean with EzyClean+Heavy duty clean with XtremeClean+

Take this sandblasted terrazzo guide with you

Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.

Important Note

Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.

Sealers Plus