Surface Finder · Terracotta

Tumbled TerracottaClean, seal & maintain guide

Tiles are turned in a tumbling drum, where contact wears down corners and creates irregular marks across the clay. Tumbled terracotta has rounded edges and a matt face that can feel gently uneven. Its open pores tend to take up spills. Often used in hallways and courtyards, this finish has Natural Look available through the Product Selector.

Looks our Product Selector recommends:Natural Look
Tumbled Terracotta close up
Other terracotta finishesSandblastedTexturedAll terracotta →

PRODUCT SELECTOR RECOMMENDATIONS FOR TUMBLED TERRACOTTA

Product Selector

Recommended for tumbled terracotta

Exactly what our Product Selector recommends for tumbled terracotta, with coats and coverage from the product labels.

Desired lookProductUse onm² per 1 L
per coat
Coats
Natural LookFloors · walls10–15Min 2
▶ Watch howWatch: Aqua-Seal Gold+
Approximate only. Coverage varies with the density, porosity, texture and absorption of the surface, weather, application method and number of coats. m² per 1 L = the min–max coverage from the product labels.
Open the Product Selector ›

BEFORE INSTALLING & GROUTING FOR TUMBLED TERRACOTTA

Installers

Before installing & grouting

StepProductm²/LCoats
Pre-grout release coating10–151
Grout Release+ coats the face before grouting so grout residue rinses off more easily.
TIP: Use Haze Away in the final rinse during the grouting process to make grout clean-up easier and help prevent grout haze.
Eff-Shield+

PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around terracotta. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed

CLEANING TUMBLED TERRACOTTA BEFORE SEALING

Step 1 · Clean

Clean before sealing

The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Haze Away
New work · grout haze & site film

Pre-seal first, then remove grout film with Haze Away. Very light haze under 10 days old: dilute 1:1 or use neat. Sponge or mop on, dwell 10 min. DON'T ALLOW PRODUCT TO DRY ON SURFACE – ADD MORE DILUTED PRODUCT TO KEEP WET AND ACTIVE. Scrub with a white (light), blue (moderate) or black (heavy) pad; stiff bristle brush on rough or textured surfaces. Rinse, dry. Heavier or older haze: see stain removal.

XtremeClean+
Existing surfaces · clean & prepare

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.

▶ Watch howDeep clean with XtremeClean+Remove organic stains with Active Plus

STAIN REMOVAL & PROBLEM SOLVING FOR TUMBLED TERRACOTTA

Problem solvers

Stain removal & problem solving

Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.

ProblemUse (try in this order)
Grout haze (heavy)
Efflorescence (white salts)
Rust & iron stains
Fertiliser
Oil, grease & food
Wine, coffee & tea
Mould, mildew & algae
Heavy dirt build-up
Hard water marks
▶ Watch howOxi Gel+ how-toRemove rust with Rust AwayRemove leaf & tannin stains with Active PlusDeep clean with XtremeClean+Which stain remover? Product Selector guide

CLEANING & CARE TIPS FOR TUMBLED TERRACOTTA

Pro tips

Cleaning & care tips

Never pressure wash. High-pressure water can exfoliate and degrade the surface and reduce the sealer's performance. It can also drive water deep into the surface and bring up mineral blooming and efflorescence. Clean with a mop, brush or scrubbing machine and rinse with a low-pressure garden hose instead.
  • Pre-seal before grouting to help reduce grout staining and make clean-up easier.
  • Let tiles dry completely before sealing.
  • Already coated (gloss / satin) floors: clean with EzyClean+ only. XtremeClean+ is a stripper, so keep it for when you want to strip and recoat.
  • Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
  • Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
▶ Watch howWeekly clean with EzyClean+Heavy duty clean with XtremeClean+

Take this tumbled terracotta guide with you

Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.

Important Note

Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.

Sealers Plus