Home > Surface Finder > Slate > Textured

Surface Finder · Slate

Textured SlateClean, seal & maintain guide

Splitting slate along its layers leaves the ridged face used for a textured finish. High and low points give it an uneven feel and catch light differently across each tile. Absorbency varies, and the recesses can collect oily dirt. Used for paving, floors and wall features, it offers Natural Look, Colour Enhanced and High Gloss.

Looks our Product Selector recommends:Natural LookColour EnhancedHigh Gloss
Textured Slate close up

PRODUCT SELECTOR RECOMMENDATIONS FOR TEXTURED SLATE

Product Selector

Recommended for textured slate

Exactly what our Product Selector recommends for textured slate, with coats and coverage from the product labels.

Desired lookProductUse onm² per 1 L
per coat
Coats
Consolidator & StrengthenerFloors · walls · benchtops2–2.51
Natural LookFloors · walls · benchtops15–20Min 2
Colour EnhancedFloors · walls · benchtops15–20Min 2
Satin NEWSatin'N'Seal*Floors · walls10–15Min 2
High GlossGloss'N'Seal*Floors · walls10–15Min 2
▶ Watch howWatch: Aqua-Seal Gold+How to colour enhance & sealHow to apply Gloss'N'Seal

* Satin'N'Seal / Gloss'N'Seal: cannot be used if Condense Plus or Ultra-Block are used first.

Approximate only. Coverage varies with the density, porosity, texture and absorption of the surface, weather, application method and number of coats. m² per 1 L = the min–max coverage from the product labels.
Open the Product Selector ›

BEFORE INSTALLING & GROUTING FOR TEXTURED SLATE

Installers

Before installing & grouting

StepProductm²/LCoats
Pre-seal top surface before installation or before grouting15–201
Pre-seal top surface before installation or before grouting15–201
Pre-seal top surface before installation or before grouting15–201
Pre-grout release coating2.5–201
▶ Watch howPre-seal with Enhance'N'Seal
Pre-sealing the top surface before installation or grouting makes grout clean-up easier.
TIP: Use Haze Away in the final rinse during the grouting process to make grout clean-up easier and help prevent grout haze.
Installers

Six-sided dip sealing

Dip sealing coats all six faces of each tile or paver (face, back and edges) before installation. It helps reduce moisture, salts and minerals from the bedding and adhesive moving into the stone, which helps reduce efflorescence, picture framing, tide marks and staining. Recommended for porous natural stone and pavers, especially in wet areas and on mortar beds.

StepProductm²/LCoats
Six-sided dip seal (all faces)2–2.51
Six-sided dip seal (all faces)2–2.51
▶ Watch howHow to six-sided seal with Condense Plus
Six-sided rates are per m² of tile / paver (all faces). Gloss / satin finish: skip six-sided sealing. Gloss'N'Seal / Satin'N'Seal cannot be used if Condense Plus or Ultra-Block are used first, on any side.
TIP: Use Haze Away in the final rinse during the grouting process to make grout clean-up easier and help prevent grout haze.
Eff-Shield+

PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around slate. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed

CLEANING TEXTURED SLATE BEFORE SEALING

Step 1 · Clean

Clean before sealing

The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Haze Away
New work · grout haze & site film

Remove grout haze and site film. Very light haze under 10 days old: dilute 1:1 or use neat. Sponge or mop on, dwell 10 min. DON'T ALLOW PRODUCT TO DRY ON SURFACE – ADD MORE DILUTED PRODUCT TO KEEP WET AND ACTIVE. Scrub with a white (light), blue (moderate) or black (heavy) pad; stiff bristle brush on rough or textured surfaces. Rinse, dry. Heavier or older haze: see stain removal.

XtremeClean+
Existing surfaces · clean & prepare

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.

▶ Watch howDeep clean with XtremeClean+Remove organic stains with Active Plus

STAIN REMOVAL & PROBLEM SOLVING FOR TEXTURED SLATE

Problem solvers

Stain removal & problem solving

Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.

ProblemUse (try in this order)
Grout haze (heavy)
Efflorescence (white salts)
Rust & iron stains
Fertiliser
Oil, grease & food
Mould, mildew & algae
Soap scum
Hard water marks
▶ Watch howOxi Gel+ how-toRemove rust with Rust AwayRemove leaf & tannin stains with Active PlusWhich stain remover? Product Selector guide

CLEANING & CARE TIPS FOR TEXTURED SLATE

Pro tips

Cleaning & care tips

Never pressure wash. High-pressure water can exfoliate and degrade the stone and reduce the sealer's performance. It can also drive water deep into the stone and bring up mineral blooming and efflorescence. Clean with a mop, brush or scrubbing machine and rinse with a low-pressure garden hose instead.
  • Skip cheap 'slate shine' coatings: they can peel and get slippery. For a gloss or satin look use Gloss'N'Seal or Satin'N'Seal (Cannot be used if Condense Plus or Ultra-Block are used first).
  • Sweep often — grit in the riven face wears it.
  • Soft or flaky slate: consolidate with Condense Plus first.
  • Going for a High Gloss or Satin look? Clean Gloss'N'Seal / Satin'N'Seal coated floors with EzyClean+ only. XtremeClean+ is a stripper, so keep it for when you want to strip and recoat. Coated floors can be slippery when wet.
  • Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
  • Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
▶ Watch howWeekly clean with EzyClean+Heavy duty clean with XtremeClean+

Take this textured slate guide with you

Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.

Important Note

Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.

Sealers Plus