Home > Surface Finder > Sandstone > Tumbled
Tumbled SandstoneClean, seal & maintain guide
Pieces turn against one another in a tumbling machine, knocking back sharp corners and adding small marks across the face. Tumbled sandstone feels worn at the edges, with uneven patches that can hold dirt. It tends to absorb spills readily and is often used for courtyards, paths and garden edging. Available looks include Natural Look, Colour Enhanced and High Gloss.

Recommended for tumbled sandstone
Exactly what our Product Selector recommends for tumbled sandstone, with coats and coverage from the product labels.
| Desired look | Product | Use on | m² per 1 L per coat | Coats |
|---|---|---|---|---|
| Consolidator & Strengthener | Floors · walls · benchtops | 1–1.25 | 1 | |
| Natural Look | Floors · walls · benchtops | 8–10 | Min 2 | |
| Colour Enhanced | Floors · walls · benchtops | 8–10 | Min 2 | |
| Satin NEW | Satin'N'Seal* | Floors · walls | 10–15 | Min 2 |
| High Gloss | Gloss'N'Seal* | Floors · walls | 10–15 | Min 2 |
* Satin'N'Seal / Gloss'N'Seal: cannot be used if Condense Plus or Ultra-Block are used first.
Before installing & grouting
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Pre-seal top surface before installation or before grouting | 8–10 | 1 | |
| Pre-seal top surface before installation or before grouting | 8–10 | 1 | |
| Pre-seal top surface before installation or before grouting | 8–10 | 1 | |
| Pre-seal top surface before installation or before grouting | 8–10 | 1 | |
| Pre-grout release coating | 8–10 | 1 |
Six-sided dip sealing
Dip sealing coats all six faces of each tile or paver (face, back and edges) before installation. It helps reduce moisture, salts and minerals from the bedding and adhesive moving into the stone, which helps reduce efflorescence, picture framing, tide marks and staining. Recommended for porous natural stone and pavers, especially in wet areas and on mortar beds.
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Six-sided dip seal (all faces) | 1–1.25 | 1 | |
| Six-sided dip seal (all faces) | 1–1.25 | 1 |
PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around sandstone. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed
Clean before sealing
The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Remove grout haze and site film. Very light haze under 10 days old: dilute 1:1 or use neat. Sponge or mop on, dwell 10 min. DON'T ALLOW PRODUCT TO DRY ON SURFACE – ADD MORE DILUTED PRODUCT TO KEEP WET AND ACTIVE. Scrub with a white (light), blue (moderate) or black (heavy) pad; stiff bristle brush on rough or textured surfaces. Rinse, dry. Heavier or older haze: see stain removal.

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.
Stain removal & problem solving
Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.
| Problem | Use (try in this order) |
|---|---|
| Grout haze | |
| Efflorescence (white salts) | |
| Rust & iron stains | |
| Fertiliser | |
| Oil, grease & food | |
| Leaf & tannin stains | |
| Mould, mildew & algae | |
| Wine, coffee & tea | |
| Red soil |
Cleaning & care tips
- Hose pool coping and surrounds after use to limit salt build-up.
- Let new stone dry fully before sealing — trapped moisture shows as patchy results.
- Going for a High Gloss or Satin look? Clean Gloss'N'Seal / Satin'N'Seal coated floors with EzyClean+ only. XtremeClean+ is a stripper, so keep it for when you want to strip and recoat. Coated floors can be slippery when wet. (Cannot be used if Condense Plus or Ultra-Block are used first)
- Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
- Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
Take this tumbled sandstone guide with you
Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.
Important Note
Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.
