Home > Surface Finder > Quartzite > Honed
Honed QuartziteClean, seal & maintain guide
Honing uses fine abrasives to level quartzite without developing a mirror shine. The result feels smooth, with softer reflections that let the grain remain visible. It is often chosen for kitchen benches, internal flooring and bathroom walls. Absorbency varies, and oils can leave marks on unsealed stone. Choose between Natural Look and Colour Enhanced.

Recommended for honed quartzite
Exactly what our Product Selector recommends for honed quartzite, with coats and coverage from the product labels.
| Desired look | Product | Use on | m² per 1 L per coat | Coats |
|---|---|---|---|---|
| Consolidator & Strengthener | Floors · walls · benchtops | 2–2.5 | 1 | |
| Natural Look | Floors · walls · benchtops | 15–20 | Min 2 | |
| Colour Enhanced | Floors · walls · benchtops | 15–20 | Min 2 |
Before installing & grouting
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-grout release coating | 2.5–20 | 1 |
Six-sided dip sealing
Dip sealing coats all six faces of each tile or paver (face, back and edges) before installation. It helps reduce moisture, salts and minerals from the bedding and adhesive moving into the stone, which helps reduce efflorescence, picture framing, tide marks and staining. Recommended for porous natural stone and pavers, especially in wet areas and on mortar beds.
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Six-sided dip seal (all faces) | 2–2.5 | 1 | |
| Six-sided dip seal (all faces) | 2–2.5 | 1 |
PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around quartzite. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed
Clean before sealing
The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.

Poultice Plus paste over the stain as per label, remove and wipe clean. Repeat if needed.
Stain removal & problem solving
Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.
| Problem | Use (try in this order) |
|---|---|
| Grout haze | |
| Rust & iron stains | |
| Fertiliser | |
| Oil, grease & food | |
| Wine, coffee & tea | |
| Mould, mildew & algae | |
| Hard water marks |
Cleaning & care tips
- Lemon test on an offcut first: if it dulls, the stone is acid-sensitive, so treat it like marble and don't use OxiTreat+ or other acid cleaners.
- Hazy or sticky after sealing = excess not wiped off; re-wet with sealer and wipe dry.
- Benchtops: ReFresh+ daily.
- Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
- Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
Take this honed quartzite guide with you
Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.
Important Note
Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.
