Home > Surface Finder > Granite > Textured
Textured GraniteClean, seal & maintain guide
Mechanical working or splitting can give granite a textured face, with ridges and hollows rather than a level shine. The exact feel depends on how the stone was worked. Common settings include garden paths, steps and feature walls. Absorption can vary widely, while recessed areas tend to collect dirt. This finish is available with Natural Look.

Recommended for textured granite
Exactly what our Product Selector recommends for textured granite, with coats and coverage from the product labels.
| Desired look | Product | Use on | m² per 1 L per coat | Coats |
|---|---|---|---|---|
| Natural Look | Floors · walls · benchtops | 15–20 | Min 2 |
Before installing & grouting
| Step | Product | m²/L | Coats |
|---|---|---|---|
| Pre-seal top surface before installation or before grouting | 15–20 | 1 | |
| Pre-grout release coating | 10–15 | 1 |
PRO TIP · EFFLORESCENCE CONTROLAdd Eff-Shield+ to the gauging water of the screed, tile adhesive or grout. As a cement bed dries, the water moving through it carries salts to the surface, causing efflorescence (white salts), picture framing and dark edges around granite. Eff-Shield+ lines the pores right through the mix with a water-repellent layer, helping reduce water absorption and the salts it brings up, while the bed can still breathe and dry out. Locked into the cement, it can't wash out or wear off. No VOC. Cement-based products only: see the label for the dose.▶ Watch howHow to add Eff-Shield+ to groutHow to add Eff-Shield+ to screed
Clean before sealing
The surface must be clean, dry and free of grout haze, dirt, grease and old coatings before sealing.

Remove grout haze and site film. Very light haze under 10 days old: dilute 1:1 or use neat. Sponge or mop on, dwell 10 min. DON'T ALLOW PRODUCT TO DRY ON SURFACE – ADD MORE DILUTED PRODUCT TO KEEP WET AND ACTIVE. Scrub with a white (light), blue (moderate) or black (heavy) pad; stiff bristle brush on rough or textured surfaces. Rinse, dry. Heavier or older haze: see stain removal.

Dilute 1:10–1:5, dwell 5–10 min, scrub, rinse twice and let dry 24–48 h before sealing. Organic staining: Active Plus first.
Stain removal & problem solving
Match the problem to the product. Where two or more are listed, try them in that order. Always test a small area first.
| Problem | Use (try in this order) |
|---|---|
| Grout haze (heavy) | |
| Efflorescence (white salts) | |
| Rust & iron stains | |
| Fertiliser | |
| Oil, grease & food | |
| Wine, coffee & tea | |
| Leaf & tannin stains | |
| Mould, mildew & algae | |
| Hard water marks |
Cleaning & care tips
- Keep OxiTreat+ off limestone, marble, travertine and concrete next to granite.
- Hose down after pool parties and BBQs.
- Benchtops: ReFresh+ daily, AquaGuard weekly.
- Routine cleaning: sweep or vacuum first, then mop with EzyClean+ (pH neutral, no rinse). Deep clean heavy-traffic areas with Stone Wash+ and use XtremeClean+ for a heavy duty clean when needed.
- Re-seal when the water drop test says so, not by the calendar: drip water on a busy spot, wait 10 minutes and wipe it off. No dark mark = still protected. If the water soaks in and darkens the surface, apply a maintenance coat of the original sealer.
Take this textured granite guide with you
Everything on this page in one printable PDF: the products, before installing, cleaning, stain removal and care tips. Print it for the job or share it with your tiler, cleaner or customer.
Important Note
Read entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application & desired results.
Sealers help reduce staining and make cleaning easier. They are not a substitute for a compliant damp-proof membrane (DPM), correct falls and drainage, or proper surface preparation.

